Super-micro-computer P4SCT Manual de usuario descargar pdf (Pagina 84)

100

C-8

SUPER P4SCT/P4SCT+/P4SCT+II User's Manual

Assigning Array Properties

Once you've create a new array, you are ready to assign the properties

to the array.

*Caution: Once the array is created and its properties are assigned,

you cannot change the array properties using the ACU. You will need to

use the Adaptec Storage Manager - Browser Edition. (Refer to Adaptec's

User's Guide in the enclosed CD.)

To assign properties to the new array:

1. In the Array Properties menu (as shown in the following screen),

select an array type and press Enter.

Note that only the available array types: RAID 0, and RAID1, are dis-

played on the screen. (*RAID 0 or RAID 1 requires two drives.)

1 2 ... 79 80 81 82 83 84 85 86 87 88 89 ... 99 100

SUPER 1
About This Manual 3
Manual Organization 3
Table of Contents 4
Chapter 3: Troubleshooting 5
Chapter 4: BIOS 6
Appendices: 6
Chapter 1 7
Introduction 7
Contacting Supermicro 8
UPER P4SCT/P4SCT+/P4SCT+II 10
Connectors Description 11
E875P & E7210 12
Processor 0 12
Motherboard Features 13
Canterwood ES (E7210) 15
Features 16
Serial ATA(SATA) Interface 16
64-bit PCI/PCI-X Interface 16
1-3 PC Health Monitoring 17
1-5 Power Supply 19
1-6 Super I/O 20
Chapter 2 21
Installation 21
2-4 Installing DDR Memory 24
Memory Speeds 25
Front Control Panel 26
2-6 Connecting Cables 27
Reset Connector 28
Overheat LED (OH) 28
GLAN1 LED 29
GLAN2 LED(*P4SCT+/ 29
P4SCT+II Only) 29
Power_LED Connector 30
*IDE LED (*See the note 30
Speaker Connector 31
NMI Button 31
IR Connector 31
Fan Headers 32
Serial Ports 32
Chassis Intrusion 33
Wake-On-LAN 33
B. GLAN1 & GLAN2 34
A. VGA Header 34
C. SMB Header 34
Universal Serial Bus (USB) 35
ATX PS/2 Keyboard and 35
PS/2 Mouse Ports 35
A. Wake-On Ring 36
B. Keylock Enable 36
B. Intel SATA LED 37
C. Marvell SATA LED 37
A. Standby PWR LED 37
2-7 Jumper Settings 38
USB Wake-Up (*USB1/2 39
Marvell's SATA Enable 39
(*P4SCT+/P4SCT+II Only) 39
Watch Dog Enable/Disable 40
GLAN2 Enable/Disable 41
Keyboard Wake-Up 41
Front Side Bus Speed 42
VGA Enable/Disable 42
Connections 43
IDE Connectors 44
Floppy Connector 44
A. AGP Slot 45
Chapter 3 47
Troubleshooting 47
Memory Errors 48
Chapter 4 53
4-2 Running Setup 54
4-3 Main BIOS Setup 54
4-4 Advanced BIOS Setup 56
USB Legacy Support 59
CPU THRM-Throttling 59
Keyboard Input Clock 59
4-4.4 PnP Configuration 61
4-4.5 Console Redirection 62
4-4.6 Hardware Monitor 63
4-5 Security 65
4-6 Boot 66
4-7 Exit 67
Load Fail-Safe Defaults 68
Load Optimized Defaults 68
Discard Changes 68
Appendix A 69
BIOS POST Messages 69
Appendix C 77
Operating System 77
ATA Operate Mode 78
Combined Mode: 78
Enhanced Mode: 78
(Enhanced Mode) 79
Managing Arrays 81
Creating Arrays 83
RAID 1 Init 85
Initializing Disk Drives 89
Rebuilding Arrays 92
Using the Disk Utilities 93
Adaptec and the OS 96
ATA RAID Controller Driver 97
Supero Doctor III 98

Comentarios a estos manuales

Sin comentarios

Super-micro-computer P4SCT Manual de usuario Pagina 84

Comentarios a estos manuales

Relacionado con productos y manuales para Hardware Super-micro-computer P4SCT