Super-micro-computer X6DHi-G2 Manual de usuario descargar pdf (Pagina 27)

Chapter 2: Installation

2-7

DDR 2 Slot

Release Tab

To Remove:

Use your thumbs to gently push near the edge of both ends of the

module. This should release it from the slot.

2-4 I/OPorts/Control Panel Connectors

The I/O ports are color coded in conformance with the PC 99 speciﬁ cation. See

Figure 2-3 below for the colors and locations of the various I/O ports.

Figure 2-3. I/O Port Locations and Deﬁ nitions

Video

Figure 2-2. Installing and Removing DDR 2

To Install:

Insert module

vertically and

press down

until it snaps

into place.

Pay attention

to the align-

ment notch at

the bottom.

1 2 ... 22 23 24 25 26 27 28 29 30 31 32 ... 119 120

SUPER 1
Preface 3
Table of Contents 4
Chapter 3: Troubleshooting 5
Chapter 4: BIOS 6
Appendices: 6
Chapter 1 7
Introduction 7
Contacting Super Micro 8
Chapter 1: Introduction 9
UPER X6DH3-G2 10
Connector Description 11
Motherboard Features 12
14
1-2 Chipset Overview 15
1-3 Special Features 16
1-4 PC Health Monitoring 16
1-5 ACPI Features 17
1-6 Power Supply 18
1-7 Super I/O 18
Chapter 2 21
Installation 21
To Un-install the Heatsink 24
(installed) 25
2-3 Installing DIMMs 26
http:www 26
DDR 2 Slot 27
Release Tab 27
Front Control Panel 28
2-5 Connecting Cables 29
Serial Ports 34
Chassis Intrusion 34
Universal Serial Bus (USB) 35
ATX PS/2 Keyboard and 36
PS/2 Mouse Ports 36
GLAN (Giga-bit Ethernet 36
Power LED/Speaker 37
Fan Headers 37
Wake-On-Ring 38
Wake-On-LAN 38
Power SMB (I 39
C) Connector 39
Overheat LED (JOH) 41
Power Supply Failure LED 41
2-6 Jumper Settings 42
Watch Dog Enable 43
CMOS Clear 43
VGA Enable/Disable 44
Alarm Reset (JAR) 44
3rd PWR Supply PWR Fault 45
Detect (J3P) 45
SAS Controller Enable (*For 45
Power Force On Enable/ 46
2-7 Onboard Indicators 47
Adaptec SAS Activity LED 48
Indicators (For the X6DH3 48
Parallel 49
Floppy Connector 50
IDE Connectors 51
Chapter 3 53
Troubleshooting 53
Memory Errors 54
Chapter 4 57
4-2 Running Setup 58
4-3 Main BIOS Setupʳ 58
Main BIOS Setup Menu 59
Multi-Sector Transfer 61
LBA Mode Control 61
32 Bit I/O 61
4-4 Advanced Setup 62
Processor Power Management 69
Hardware Monitor Logic 73
CPU Temperature Threshold 73
4-5 Security 74
Set User Password 75
Fixed Disk Boot Sector 75
Password on Boot 75
4-6 Boot 76
4-7 Exit 77
Appendix A 79
BIOS POST Messages 79
Appendix B 85
BIOS POST Codes 85
POST Code Description 86
Appendix C 91
The Enhanced Mode: 92
The Combined Mode: 92
RAID 1 Init 99
Initializing Disk Drives 102
Rebuilding Arrays 105
Managing Arrays 107
Deleting Arrays 108
*Warning 108
Creating Arrays 108
Assigning Array Properties 109
Adding a Bootable Array 110
Using the Disk Utilities 115
Operating System 117
ATA RAID Controller Driver 118
Supero Doctor III 119

Comentarios a estos manuales

Sin comentarios

Super-micro-computer X6DHi-G2 Manual de usuario Pagina 27

Comentarios a estos manuales

Relacionado con productos y manuales para Hardware Super-micro-computer X6DHi-G2